Windows, Doors & Insulation — DIY Cost Estimates
Materials costs for windows, doors, insulation, weatherproofing, shutters, and soundproofing.
⚡ Get your free AI estimate →- Crawl Space Insulation$850 – $2,400
- Spray Foam Insulation$850 – $2,400
- Insulation Removal$200 – $800
- Radiant Barrier Installation$300 – $1,200
- Attic Remodel$3,500 – $8,500
- Window Blinds Installation Or Replacement$150 – $850
- Window Tinting$150 – $400
- Sliding Glass Door Installation$800 – $2,500
- Screen Door Installation$150 – $450
- Storm Door Installation$300 – $800
- Pocket Door Installation$320 – $950
- Weather Stripping$80 – $320
- Screen Installation Or Replacement$150 – $850
- Shutter Installation$300 – $1,200
- Hurricane Shutter Installation$1,200 – $3,500
- Soundproofing$350 – $2,800
What windows, doors & insulation projects cost in materials
Materials run $80 to $8,500 across 16 projects. Weather stripping is the cheapest at $80 to $320, then window blinds installation at $150 to $850 and window tinting at $150 to $400. The top is an attic remodel at $3,500 to $8,500, which is really a room build rather than a window swap. Below that, hurricane shutter installation runs $1,200 to $3,500 and soundproofing $350 to $2,800. All materials only, with no labor included.
Where the DIY line sits
No project here rates Advanced. Eleven of the 16 are Intermediate and 5 are Beginner: weather stripping, window blinds, screen door installation, screen replacement, and shutter installation. The practical meaning of Intermediate here is measure twice and seal properly. Insulation work is the part to respect, not because it is complex but because attics carry heat stress, fiberglass and spray foam need real respiratory protection, and you can bury soffit vents or cover recessed cans and cause problems you will not see until spring. Attic remodel is a build, not a weekend.
What moves the price
Opening size and count drive windows and doors, and standard sizes cost far less than anything custom or non-rectangular. Glass package matters: single, double, low-E, and impact-rated glass are separate price tiers, which is why hurricane shutters run high. For insulation, square footage and target R-value set the material volume, and spray foam sits above batts and blown-in per square foot. Soundproofing scales with mass, so channel, clips, and dense board add up fast.
Frequently asked questions
What is the cheapest way to cut drafts in my house?
Weather stripping is the cheapest project in this category at $80 to $320 in materials, and it rates Beginner. That covers door sweeps, foam and V-strip, threshold seals, and caulk for a whole house. Window tinting at $150 to $400 helps with solar gain rather than air leakage. Both are materials only, so the cost is what you carry out of the store.
Can I finish an attic myself?
An attic remodel estimates at $3,500 to $8,500 in materials and rates Intermediate, but that assumes the space is already framed to carry a floor and finished space. NailIt declines structural and load-bearing changes and electrical panel work. Adding dormers, cutting rafters, sistering joists to take live load, or running a new circuit to a panel all belong with licensed pros.
How much do hurricane shutters cost if I install them myself?
Hurricane shutter installation estimates at $1,200 to $3,500 in materials for a house, covering panels or accordion units, tracks, anchors, and fasteners. Opening count and width drive the number. Check your local wind-borne debris requirements before buying, because rated products and approved anchoring can be what an inspection or an insurance discount depends on.
Estimate your next windows, doors & insulation project
Free AI breakdown — materials, costs, tools, steps, and where to buy.
⚡ Start your free estimate →